Floorboard Inserts

How about an inexpensive way to accent your stock running boards? Our stainless steel inserts bond into the slots of your floorboards and sit just below the surface of the rubber. Comes complete with adhesive.

Fits Yamaha Road Star, Royal Star, RS Venture.

Installation: Prep the floorboard rubber by cleaning with rubbing alcohol or acetone. We provide a Loctite brand of Gel adhesive but because the rubber surface is non porous, any other comercial grade, clear adhesive may be more effective in creating a long lasting bond. Unfortunately we cannot replace lost inserts.

AM-8260SSP YAMAHA FLOORBOARD INSERT SET $52.45/pair

Floorboard Cruisin' Pegs

The Cruisin' Floorboard Pegs mount to your stock running boards, are chrome plated to match the brake and shift lever and will not conflict with engine guard bars. Pegs also retract for safety or for maneuvering in tight areas. Heavy-duty construction utilizing laser and CNC technology. A must for long rides!

Fits Yamaha Road Star, Royal Star, RS Venture and V-Star 1100 Classic.

Please note: Cruisin' Floorboard Pegs work best for riders 5'-9" and above.

Yamaha Highway Pegs for Road Star & Royal Star

A chrome plated, billet aluminum hiway peg system made to bolt to the stock Road Star and Royal Star Engine Guards.

The Hiway pegs clamp to the top part of the 1" bar and has a billet peg that folds in. The clamp measures 5" as does the footpeg.

Yamaha PullBack Risers

Our PullBack Risers come with their own "split caps" for mounting. The PullBack Risers are simple to install and best of all, do not require any drilling of the triple clamps!

Chrome Motorcycle Bullets

Conceal that unsightly front axle in a new and stylish way. Slide Aeromach's Fork Bullets over the bottom of the fork slider and simply tighten two set screws. Sleek design. Extreme eye catcher!

Chrome Motorcycle Bullets

Conceal that unsightly front axle in a new and stylish way. Slide Aeromach's Fork Bullets over the bottom of the fork slider and simply tighten two set screws. Sleek design. Extreme eye catcher!

Master Cylinder Covers for Yamaha

These CNC machined, chrome-plated aluminum covers replace your generic stock master cylinder covers. Comes complete with stainless-steel button head replacement screws.

Available in your choice of smooth or milled finish.

Will Not fit V - Star 1100 or 650

Royal Star

AM-5080C YAMAHA MASTER CYLINDER COVER - smooth $41.95/pair

Master Cylinder Covers for Yamaha

These CNC machined, chrome-plated aluminum covers replace your generic stock master cylinder covers. Comes complete with stainless-steel button head replacement screws.

Available in your choice of smooth or milled finish.

Will Not fit V - Star 1100 or 650

Master Cylinder Covers for Yamaha

These CNC machined, chrome-plated aluminum covers replace your generic stock master cylinder covers. Comes complete with stainless-steel button head replacement screws.

Available in your choice of smooth or milled finish.

Will Not fit V - Star 1100 or 650

Yamaha Road Star

AM-5085C YAMAHA MASTER CYLINDER COVER - smooth $20.99/ea

Master Cylinder Covers for Yamaha

These CNC machined, chrome-plated aluminum covers replace your generic stock master cylinder covers. Comes complete with stainless-steel button head replacement screws.

Available in your choice of smooth or milled finish.

Will Not fit V - Star 1100 or 650

Diamond Master Cylinder Covers

New "diamond-cut" master cylinder cover design!

Diamond Master Cylinder Covers

New "diamond-cut" master cylinder cover design!

Chrome Fusion Master Cylinder Clamps

Chrome Fusion replaces your ugly, stock grey master cylinder clamp.

Some bikes will require two Chrome Fusion clamps. Make your selection below (Note: does not fit Royal Star)

.
AM-9930C YAMAHA CHROME FUSION CLAMPS - pair $52.45

Baron's Bullet Tachometer

This is the accessory you've all been waiting for! Baron's universal Bullet Tach features a compact "snub-nosed" design with styling that provides a sleek but aggressive look to your bike. Uniquely designed, Baron's Bullet Tach can mount in several locations on the handlebar, accommodating any other accessory you may have already installed. Bolt the tach to your desired location, pop-off the tach's removable bezel, and simply rotate the tach face back to vertical for a perfect view.

This chrome-plated assembly comes complete with an accurate, 8000-rpm electronic mini-tach that provides critical rev information at a glance. Concealed wiring routes from bottom of tach's handlebar clamp and connects easily to your bike's ignition coils with provided crimp-on connectors.

Will fit all motorcycles with 1-inch handlebars, with or without windshields. A totally custom look that's fully functional! Now available with a white-faced dial option and in sizes to fit either 1-1/4" or 1-1/2" handlebars.

Tach measures 3 1/2" in length by 3.0" in diameter

YAMAHA BULLET TACH - 1" Handlebar $199.00

Fatty Pullback Risers for 1 1/4" Fat Bars

Did you ever want to use a 1.25" handlebar on your bike but couldn't get it to work because the riser spread on your metric bike was wider than American bikes? We thought those thick bars would look great so we stepped this special riser to fit all varieties of 1.25" handlebars, whether they are White Bros Burly Bars, Wild 1 chubbys or Drag specialities, our risers will make them work. Pictured is a 1.25" White Bros Burly Bar-Classic.

Fits Road Star Only

Iron Cross Brake Light -Chrome Billet

A total of 45 RED LEDs. Comes with dual intensity (high/low). Our Iron Cross can be used as a flushmount (by separating chrome bezel and lense from the bucket then sandwiching the bucket and LEDs behind the fender /bag and bolting to the chrome bezel and red lens on the outside) or straight mounted on the outside of motorcycle fenders, saddlebags. or car fenders.

Sold individually.

Dimensions: 2.25"Length x 2.25"Height x .85"Depth

Iron Cross Turn Signals - Chrome Billet

Can be mounted to the rear fender. Comes with dual intensity (high/low). All LEDs function in running mode.

Dimensions: 2.25" Length x 2.25" Height x .85" Depth
A total of 45 RED LEDs.

LED Replacement for Stock Yamaha Road Star/V Star Tailight

AM-4480 TAILIGHT, BRAKE LIGHT AND TURN SIGNALS $134.99 ea.

Reptile Brake/Clutch Reservoir Covers

Flame Brake/Clutch Reservoir Covers

Comes complete with two stainless-steel button head replacement screws for ultra-clean look! Available in singles-$20.95 or pairs- $41.95 depending on your bike. Please check the hand controls on your metric bike to determine if you have a manual clutch or hydralic. A single cover is all that is needed for manual and a pair for bikes with hydralic clutches and brakes.

*Note, will not fit: VStar or 96' & older Honda models.

Star Brake/Clutch Reservoir Covers

We asked our parts designer to come up with yet another billet, "Star" part and this was his creation. The cover replaces your generic stock master cylinder cover and comes complete with stainless-steel button head replacement screws. Sold in singles only. Fit all Road Star models.

AM-5085STARC Brake/Clutch Reservoir Covers for Road Star $20.95 ea

Vertical License Flame Accent

Made from polished stainless steel. This wicked flame bolts to the bottom, backside of the license frame and hangs down. A must for a bike with a flame paint theme.

Biker for Life License Frame

"Ride Hard, Ride Free....Biker For Life"

This chrome frame is machined from T6 aluminum and fits all license plates that measure 7"L X 4"W. Comes complete with stainless steel mounting hardware.

LED Illuminated License Frame

35 Degree Drag Bar with 1" Diameter

• 35 degree bend
• 12" of pullback
• 8" Center
• 28.5" Width

Chrome Handlebar without knurls or dimples - cannot run cables through bars

Star Billet Brake Pedal

We asked our parts designer to come up with a billet brake pedal for the Star and this was his creation. This chromed, billet aluminum brake pedal measures 5" Long X 2" Tall and installs easily. Simply peel off the stock rubber and slide the Star Billet Pedal in place. Lock down the four set screws on the back side and you are ready to go.

For Road Star only. V Star coming soon.

Billet Warheads for Front Axle Concealment

Drop the bomb! The next generation has arrived. Are you ready?

These mean little monsters slide over your forks and are designed to portray aggressive, unruly and unsocial behavior. Forget what everybody else is bolt'n on their bike! You lead the trend.

Guaranteed to make em circle and stare at the next rally.

Warheads are machined from extruded billet aluminum and chrome plated.

They bite on with two set screws per part.

Fits Road Star, Royal Star, V Star 1100.

Come in Smooth and Speed Milled.

Billet Warheads for Front Axle Concealment

Drop the bomb! The next generation has arrived. Are you ready?

These mean little monsters slide over your forks and are designed to portray aggressive, unruly and unsocial behavior. Forget what everybody else is bolt'n on their bike! You lead the trend.

Guaranteed to make em circle and stare at the next rally.

Warheads are machined from extruded billet aluminum and chrome plated.

They bite on with two set screws per part.

Fits Road Star, Royal Star, V Star 1100.

Come in Smooth and Speed Milled.

AM-3650C SPEED MILILED BILLET WARHEAD $134.95 pair

Tailspikes now available for V Star & Road Star

Aeromach's Tail Spikes are made of polished stainless steel and thread into the fender strut replacing the stock allen head bolts. They keep the curious from getting too close!

7 inch "Chopper Risers" for Yamaha

Looking for risers that have attitude? Chances are, if you wanted a chopper style riser, you had to buy a set that were made for HD and you had to modify your bike. We designed these risers to bolt right on to metric bikes with M12 or M10 and we supply the hardware. They work extremely well with 18, 25 & 35 degree drag bars in 1 inch diameter.

For most bikes, longer control (clutch and brake) cables will be needed depending on the drag bar you select. Installation is simple and the top bolts are concealed by the cap. You select your style of caps: "Dome" or the radical "Tribal". The 7" risers are chrome plated and made from extruded billet aluminum. Come with hardware for installation.

AM-3900C YAMAHA MOTORCYCLE RISERS with Domed Cap $134.95 Pair

7 inch "Chopper Risers" for Yamaha

Looking for risers that have attitude? Chances are, if you wanted a chopper style riser, you had to buy a set that were made for HD and you had to modify your bike. We designed these risers to bolt right on to metric bikes with M12 or M10 and we supply the hardware. They work extremely well with 18, 25 & 35 degree drag bars in 1 inch diameter.

For most bikes, longer control (clutch and brake) cables will be needed depending on the drag bar you select. Installation is simple and the top bolts are concealed by the cap. You select your style of caps: "Dome" or the radical "Tribal". The 7" risers are chrome plated and made from extruded billet aluminum. Come with hardware for installation.

6  Inch Pullback Risers - Long Necks

Not happy with your equipment? Are your parts lacking in length? If 4 inches of rise is just not enough for you and your passenger, then we have your aid. Aeromach has added 2" to make a 6" pullback riser that works with factory cables. They work great with drag bars.

Tribal Flame Grips

Tribal Flame Grips made from solid T6 billet aluminum. These billet grips are chrome plated and have a unique tribal flame pattern. The caps at the end are threaded and can be removed to add a mirror to the end of the left grip.

AM-2350C Tribal Flame Grips $119.95 Pair

Smooth Grips

The Billet Grips are made from solid T6 billet aluminum. These machined grips are chrome plated and perfectly smooth. The caps at the end are threaded and can be removed to add a mirror to the end of the left grip with Aeromach's "Grip End" piece. The billet grips are for 1" diameter handlebars and fits almost all metric cruisers. The stock handlebars on metric bikes are 1" diameter.

AM-2400C Smooth Motorcycle Grips $119.95 pair

Grip End piece for Mounting Mirrors to Aeromach Grips

The Grip End piece allows you to add an Aeromach mirror to the end of your Aeromach grip (left side only). Simply remove the threaded cap from the left side and thread on the Grip End pc. Then select an Aeromach mirror to attach to the end of your grip. We find that the small oval, large oval, classic round and street fighter look the best.

*Note, mirrors are sold seperately.

AM-2285LC Grip End for mounting Aeromach motorcycle mirrors (left) $46.95

Get Back! Leather Straps

The Get Backs! clip to your clutch lever and have a quick release so you can
remove them at a moment's notice. This Old School strap is convenient for
annoying dogs that like to chase bikes.

The strap is 29" in length and available in black only. Fits all clutch
levers.

AM-GBLS Leather Get Backs $50.00 ea

Billet Drink Holder & Stainless Steel Cup motorcycle drink holder

A cup holder that really works! Keeps coffee hot and water cold (not to mention anything else you put in it). Made to mount most anywhere on a handlebar.

Available in Chrome, Black or Silver Anodized. 1" or 1.25" bars.
a.. Patented bracket and faceted ring are constructed of machined aluminum.
a.. 16-oz. cup is 100% stainless steel-insulated and spill-proof.
a.. Detachable components make the task of storage quick and efforless.